Atlas 412 12,000 LB. 4 Post Lift:

The Atlas 412 12,000 pound capacity four post lifts are designed and built to commercial grade standards and will provide many years of service. Our Atlas lifts offer many exclusive features not found on many other competitor's lifts.

How Do I Get My Stuff Off The Truck?:
Many customers do not have access to loading docks and forklifts. We have assembled some photos of our products being unloaded with and without the aid of a forklift. Many of our freight carriers have power tailgates on their delivery trucks. There may be an extra charge for the power tailgate, depending on the carrier. The power tailgate is normally rated at 1000 LB. capacity. This is not enough capacity to unload most of our lifts. However, when used properly (and safely), the power tailgate (in conjunction with some common sense) allows the customer to off load many of our products without the use of a forklift.
Watch our video on how to use a power tailgate to help you unload your product from a truck.

Most truck shipments will be delivered by a commercial freight carrier operating a tractor/trailer rig. The semi trailer will be enclosed. Most commercial carriers have smaller straight trucks and some have small flatbed trucks, but the majority of freight companies will not use these smaller trucks for your delivery. Greg Smith Equipment cannot guarantee the type of truck that will be used for delivery. You should assume that your product will be delivered on a tractor/trailer rig that uses a 53 foot enclosed trailer. This is a VERY LONG rig. It is the truck driver's responsibility to make sure that your product is brought to the back of the delivery truck. It is the customer's responsibility to unload the product from the truck.
Watch our video on how to unload your two post or four post lift from a semi truck.

Features:
The Atlas 412 (12,000 LB. capacity four post lift) incorporates many structural and cosmetic features that are found on lifts costing thousands of dollars more money. The Atlas 412 is tested to ensure that this lift system will perform flawlessly at its rated capacities. The Atlas 412 has been manufactured to the same exacting specifications for many years.

The Atlas 412 uses a high strength cable system (with a under runway oversized hydraulic cylinder) powered by a 220 volt (single phase) power unit to raise and lower the lift. Many competitors use an "old style" chain lifting system with an exposed hydraulic cylinder system. Old style chain lifts are difficult to "level" properly and the exposed hydraulic cylinder is responsible for numerous "door dings".

The Atlas 412 four post lift incorporates a lock ladder system in each column and all four column locks are simultaneously air activated from the power unit column. The runways are bolted to the cross tubes, but can be adjusted (moved in) if needed.

---

Atlas RJ-6000 Rolling Jacks:

The Atlas RJ-6000 is a heavy duty rolling jack designed to lift and support 6,000 LB. The commercial grade RJ-6000 rolling jack can be used to raise the front or rear portion of a vehicle; allowing the operator of a four post above ground lift to perform wheel and brake service. Most commercial shops buy two of these hydraulic rolling jacks, so that the entire vehicle can be supported in the air at the same time.

The Atlas RJ-6000 has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS that are located over the runways of the four post lift. The Atlas RJ-6000 rolling bridge is equipped with expandable supports which adjust to fit many different brands of four post above ground lifts. These supports have a unique roller system that allows the rolling hydraulic jack to glide easily under the entire length of the vehicle. The large heavy steel wheels allow the rolling jack to be positioned under the correct lifting points in a matter of seconds.

The Atlas Atlas RJ-6000 comes standard with a set of peg style truck adapters which increases the lifting height of the lift pads. These truck adapters will allow the Atlas RJ-6000 rolling hydraulic jack to raise most pick up and larger trucks that will sit higher than the average passenger car.

The Atlas RJ-6000 can be equipped with an optional Atlas Air/Hydraulic Pump. The air/hydraulic pump would require a supply of compressed air (air compressor) to work properly.

The Atlas RJ-6000 rolling hydraulic jack features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas RJ-6000 are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).

"World-Class" Products:
Greg Smith Equipment is proud to state that our manufacturers are definitely "world-class". Our Atlas products are sold throughout the world.

Instruction manuals that accompany products may contain certain specifications that do not apply to the product when used in the USA or Canada.

IE:
Electrical voltage requirements are different in the USA compared to other countries. There may also be certain accessory items that need to be included for Europe, but are not needed in the USA.

The Greg Smith Equipment Sales website contains accurate electrical (and accessory) information (for use in the USA or Canada) about your product.

Please review the GSES website and discuss electrical (or accessory) questions with your salesperson before placing your order.

Atlas 412 Four Post Lift
Capacity	12,000 LB.
Lifting Height	75 ½" (6' 3 1/2")
Overall Width of Columns (Without Motor)	126" (10' 6")
Overall Width of Columns (With Motor)	135" (11' 3")
Overall Length with Approach Ramps	230" (19' 2")
Overall Length without Approach Ramps	200" (16' 8")
Length Between Columns	184 ¼" (15' 4 ¼")
Runway Length	186 ½" (15' 6 ½")
Runway Width	22" (1' 10")
Thickness of Runway	7"
Width Between Runways	44 ½" (3' 8 ½")
Width Between Runway Rails	42" (3' 6")
Outside Runway to Outside Runway	84 ¾" (7' ¾")
Clearance Under Runways	68 ¼" (5' 8 ¼")
Column Dimension	7" x 5"
Base of Column	10 1/8" x 9"
Clearance Between columns	112 ¼" (9' 4 ¼")
Height of Columns	82" (6' 10")
Maximum Wheel Base	185" (15' 5")
Drive Thru	98 ½" (8' 2 ½")
Cable Diameter	1/2"
Motor	2 HP, 220 Volt, Single phase
Shipping Weight	2,400 LBS.

Requires a minimum of 4" of concrete with 3000 psi.

Atlas RJ-6000
Maximum Width	55 ¾"
Minimum Width	35"
Distance Between Runway Capability	32"-52"
First Locking Position	7"
Second Locking Position	10 1/2"
Maximum Lifting Height (With Adapters)	20 1/4"
Adapters	3" and 1 ½"
Maximum Capacity	6,000 LB.

	Size:	Pages:
Atlas 412 Manual	1.3 MB	22	Download

View our Shipping Policies