 |
 |
 |
|
Call For Availability!
Description:
The Direct Lift Pro 9F is a commercial grade two post car lift. This above ground lift is perfect for those customers who need a base plate lift. If you have a low ceiling height in your work area, then the Direct Lift Pro9F is the perfect choice for a base plate lift.
The columns on the Direct Lift Pro9F are 9’3” tall, so this car lift can be installed in most garages with only a 10’ ceiling. This 9000 LB car hoist weighs over 200 LB. more than our Direct Lift HR 8000 base plate two post car lift. The Direct Lift Pro 9F is a commercial grade car lift and should not be confused with many of the cheap above ground car lifts that are marketed by certain competitors as 9000 LB or 10,000 LB. capacity car lifts.
Dual Point Safety System:
The Direct Lift Pro 9F has a dual point safety release system. Most above ground base plate lifts incorporate this dual point safety release system because the single point safety release system works better on the two post overhead above ground lifts.
Two Post Secondary Lock System:
Greg Smith Equipment is pleased to introduce the new Two Post Secondary Lock System.
For more information Click Here.
Hydraulic Cylinder Configurations:
There are two popular hydraulic cylinder configurations used in two post electric/hydraulic above ground lifts:
Greg Smith Equipment sells above ground lifts that incorporate both the direct drive cylinder configuration and the chain-over-roller cylinder configuration.
The base plate two post above ground lift implements the chain-over-roller configuration. This is the only hydraulic cylinder system that is possible in the base plate lift. The base plate two post above ground is designed for “low ceilings”. The direct drive hydraulic cylinder configuration cannot be used in the base plate lift because the hydraulic cylinder would extend above the 9’ 3” column when the lift arms were raised to the maximum height.
The “overhead” two post above ground lift may incorporate either the direct drive hydraulic cylinder or the chain-over-roller hydraulic cylinder.
Flow Restrictor:
Greg Smith Equipment is proud to announce that many of our two post and four post lifts manufactured in our off shore factory (after 08-01-07) have flow restrictor valves installed in the hydraulic system. Some lifts do not require a flow restrictor.
Symmetrical Columns And Arms:
The Pro 9F has symmetrical columns and symmetrical arms. This above ground lift has a diamond plated base plate that covers the hydraulic lines and equalization cables that run across the floor between the columns.
Two post base plate lifts CANNOT BE ASYMMETRIC! (Click Here)
Power Unit:
The Direct Lift Pro9F is powered by a 220 Volt (single phase) power unit that can be mounted on either side of the above ground lift.
Electrical Requirement:
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz. We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit has a short pigtail (no plug) that can be wired to either a quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is recommended.
Click here to read more...
Installation:
The Direct Lift Pro 9F is sold as a complete above ground lift with a full set of solid peg truck adapters and the mounting hardware needed to mount the above ground car hoist.
Most of our above ground lift customers install their own car lifts. The average time to assemble the Direct Lift Pro 9F car lift is four hours.
We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.
Safety Labels:
In a concerted effort to improve customer awareness as to the correct operation of our two post and four post above ground lifts, the factory is affixing the ANSI (ALI/101S) safety labels to our Atlas and Direct above ground vehicle lifts (after 08-01-07). These ANSI (ALI/101S) safety labels help to alert the operator as to certain potential dangers that may exist in the normal operation of the lift.
Parts:
Greg Smith Equipment stocks a complete inventory of lift parts for all the lifts we sell. Lift
parts and technical support personnel can be found at all three of our locations.
Certain competitors do not stock the lifts they advertise and do not stock any of the lift parts or accessories. Lifting a car is serious business.
Call the professionals at Greg Smith Equipment.
Concerned with after sale service? Click here.
Warranty:
For information on our two post lift warranty please click here
|
|
|
|
|
|
 |
|
 |
|
Features
Symmetric Arms
Commercial Grade
Baseplate Design
Atlas Power Coat powder coat finish
9,000 lb. capacity
Designed for low ceiling clearance - 9'3" columns
Free Truck Adapters
Mounting Hardware Included
5 Year Structural Warranty, 1 Year Power Unit and Cylinders Warranty
|
|
|
 |
|
 |
|
|
| People who purchased this also bought... |
|
|
|
|
